If the water purifier is properly maintained, it can work for 4 to 5 years without problems. After that, you can start facing some common water purifier problems. Water leakage is not the only problem of common water cleaners faced by people. There are various other problems that can appear after several years of use of cleaning water, including unusual taste, unusual odor, noisy faucet, and slow output water. In this article, we have registered 5 of the most common water purifier problems and the solution so you can easily identify the problem and fix it.
5 The most common water cleansing problems and solutions
RO and UV water purifiers are the most common water purifiers found in most homes, and each can have some problems. However, we have made a list of 5 of the most common water cleansing problems and tries to list their distinctive solutions.
- Unusual water taste or smell of water purifier
If your RO or UV water purifier offers water with an unusual smell or taste, it can be because biofilms have accumulated in one or more parts of the water purifier. Biofilms are layers of organic and inorganic materials collected on the surface of water purifiers. Because of this, the level of contaminants in water rises. The fastest solution for this is to replace clogged filters or membranes. After the filter and membrane are changed, you can check whether there is an increase in the taste or smell of water. Make sure the high flow filter is changed every 12 months.
Purifiers ro uses copper tubes in their mechanism. If you note that water has a metal flavor, it means water may dissolve a number of high sulfate, chloride, and bicarbonate from the copper tube, leaving the taste of metal in the water. Similarly, if you find water from the cleaners become a little salty, it means salt and other solids are late in the water. RO water cleaners need fully functional to remove these particles from water. If the water from your cleaners feels more salty than usual, you must call a professional for maintenance checks and get cleaned cleaners. You have to do this procedure every 6 months.
- slow water flow from water purifier
If your water cleanser releases a purified water very slowly and fills only half a glass at the same time, it’s because you have a low volume or low water pressure. RO usually requires a minimum pressure of 40 to 60 psi (pound per square inch) to operate correctly. Maybe there is also damage to the cleaning water storage tank, which leads to this problem. Cleaning water storage tank contains air bladder so as to release water quickly. The more water, the higher the pressure.
If there is a leak in the bladder, it may not offer sufficient release pressure and that leads to slow water flow from the water purifier faucet. It is also possible that the water filtridge has been clogged because of a high sediment content, which can cause slow water output. If the filter is clogged, describe them replaced by a professional water purifier service.
- Faucet water purifier makes unusual sounds
If you hear a strange sound of your water cleanser faucet, especially after replacing filters and membranes, it’s because the air is pushed out of the system. It can also be due to changes in water pressure in the system. Immediately after replacing the filter, if the noise does not subside, call professionals to check whether the tube is installed correctly. Noise can also occur if the water tank valve is not correctly closed. - Water leaks from cleaning taps or filters / membranes
If there is a constant water leak from the cleaning faucet, the part of the cleaner may not be installed correctly. To fix this problem, the non-installed part needs to be identified and replaced or closely installed. If the same problem is found in a filter or water purifier membrane, it can be caused by O-RING obsolete. O-ring is a soft rubber ring that stops water from leaking from the section.
If water purifier leaks water from faucet, filter, or membrane, contact the service engineer to check whether the valve is closed correctly and if the O-ring is in good condition. If O-Ring has been cracked or not in good condition, they need to be tightly installed to be replaced.
- RO water tank is not filled
Another common problem found in many ROs and UV water purifiers is that water storage tanks are not fully charged. This is due to very low water pressure on cleaners. As we mentioned before, RO water cleaners need a minimum pressure of 40 to 60 psi (pound per square inch) to operate correctly. If water pressure is less than 40 psi, you need to increase pressure, which can be done with the help of the water pump.
The damaged RO membrane can also be a possible reason for the water tank not fully charged. Membrane RO SemiPermeable is a barrier that allows only water molecules to pass through the other side while blocking the passing of water contaminants such as dust, dirt, viruses, and bacteria, so offering clean and safe drinking water. When membranes are clogged after several months of use, the water filtration process slows down and water quality decreases. If the membrane is clogged or damaged, it must be replaced to avoid health problems.
A ro membrane in water purifiers usually needs to be replaced once a year, depending on its use. This ensures clean and healthy drinking water.